Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Knowing Essential Plumbing Skills is Important When Installing a Bathtub
Blog Article
They are making a number of good pointers on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround in general in the article further down.
Installing a bathtub isn't exactly brain surgery, however it does need solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably difficult project. If the old tub is easily easily accessible, the job can relocate immediately; if you have to open a wall surface to get rid of the old bathtub and place the brand-new tub, the job is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly require a helper to vacate the old bathtub as well as set in the brand-new one. Make certain you have certified on your own for the job and also are comfortable attempting it. As opposed to hiring a service provider to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might need a professional plumber to make tube links.
This article will aid you set up a brand-new tub in your restroom if you have currently purchased a brand-new tub and do not need to transform the arrangement of your previous water supply pipelines.
Your tools as well as product checklist need to comprise the following:
Planning for the Setup
To start with, the supporting frame supplied with the bath needs to be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps unit to stop stress on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps making use of 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use all of the provided washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome because of the limited access that is often the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a fabric all set for the remaining water that will certainly come from the pipelines. As soon as the supply pipelines have actually been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the brand-new taps. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing both wooden boards under its feet, place the bath tub in the needed placement. The wooden boards are useful in equally spreading the weight of the bath tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by inspecting the level and also changing the feet on the bath tub till the spirit level checks out degree.
To mount faucets, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise check the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as explained in the supplier's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has actually been used at least when as this will certainly resolve it into its final position.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly require a plastic port to prevent damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area in between the faucet and the sink. Secure the tap in place with the supplier offered backnut. When the tap is firmly in position, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet ports. The former type ought to be attached to the faucet ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bath as well as the tiling, causing difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes as well as cartridges, and also can sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water before securing, to allow for the motion experienced when the tub remains in use. The sealant can break rather very early if you do not take into consideration this activity prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally easily readily available on the marketplace. It is suggested to fit the floor tiles making use of waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Place feedback directly below. We would be delighted to find out your reactions about this blog post. We hope to see you back again before long. Those who appreciated our article if you please don't forget to share it. Thank you for your time. Kindly check our website back soon.
Fast service, dial quick! Report this page